Skip to content

Updater Tool Tutorial

UPDATER TOOL TUTORIAL

The updater tool is a software used to update the firmware on your units to the latest version(the process is only supported on MS Windows OS)

There are two main steps after the installation of the program, the first is to ensure the PC requirements and the drivers needed for the update process are properly installed and the second step it updating the Firmware.

it worth mentioning that the first step is required to be done only once on a given PC.

0.0- Updater Tool Installation

After downloading the zip you can unzip and run the installation file. Consider after installation you need to run the program in administration mode by right click > run as administrator.

0.1- Run as Administrator

You need to run the program in administration mode by right click > run as administrator.

admin

1.0- PC Driver Installation

To execute the Driver installation process click on “Install PC driver” you can find the button in the PC requirements menu.

drivers

NOTE:
– Run the program in Administrator mode
– This step is required only one time on the same PC
– if an error happens on this step you can check the Troubleshooting section HERE

2.0 Firmware Update Process

This process will actually update the firmware version of your device, the main steps are:
1) Turn OFF your unit and Make sure your unit is NOT in DFU mode ( please check user manual section for your device to learn how to make sure the unit operates in Normal mode and not in DFU mode)
2) Power up the unit and make sure the USB cable is connected, in this case “E2” LED will start blinking which states the unit is in Normal operation.
3) A new COM port will be detected for SOLO, please select the proper USB COM port of SOLO
4) Identify the SOLO Unit
5) Turn OFF the unit and Put SOLO in DFU mode, Wait 5 second, Turn ON the unit and perform the Firmware update.

All the steps are performed in the Update Firmware menu of the Updater tool.

updates

NOTE:
– Run the program in Administrator mode
– if an error happens on this step you can check the Troubleshooting section Here

2.1 Select the USB port

COM selection

This step requires you to select the correct COM port where your device is connected. Your unit needs to be connected to the USB using a USB data cable and be in operational mode (E2 LED is blinking), same way as communicating with your unit using Motion Terminal.

After the selection of the port, you can instantly go to the next step by pressing “Detect the unit” button

NOTE:

– During the updating process don’t reuse the USB port on your device for other purposes (eg. staying connected to Motion Terminal)

– For this part the unit has to be in Operational Mode (E2 LED is blinking), and if you are in DFU mode you can’t see the COM port and you need to put the unit back into Operational mode ( Turn OFF, disconnect the Jumper or Switch on the DFU pin, Turn On the unit)

2.2 Unit Identification

ID solo

This action is fully automated, after pressing the “Detect the Unit” button the Updater will run the task, and when it positively finish it will show you the “Update” button

NOTE:

– If the process is not successful you can retry it by turning off-on your unit with at least 5 seconds between OFF to ON state.

– For this part the unit has to be in Operational Mode (E2 LED is blinking), and if you are in DFU mode you can’t see the COM port and you need to put the unit back into Operational mode ( Turn OFF, disconnect the Jumper or Switch on the DFU pin, Turn On the unit)

2.3 Updating the Unit

Before running the Update task you need to put your unit in DFU Mode, the process is different by the model and you can read more on the specific user manual, after that you can run the updating process that will take around a minute.

In short, the DFU steps are:
Step 1: Turn OFF the motor controller and wait for 5 seconds
Step 2: Put the Unit in DFU mode
Step 3: Turn ON the motor controller and wait for 5 seconds

NOTE:
– When solo is in DFU mode the E2 and E1 LEDs remain ON, in operational mode E2 LED is blinking.

update step3

Conclusion

This is a tutorial to help with firmware updates, in case of an error is possible to check the Troubleshooting section Here which listed common problems you can encounter.

For any support, please get in touch with us.

Drive your next innovation today

Discover our High-Performance Motor Controllers, Test Benches, and Services trusted worldwide.