Tech Specs – SOLO MINI
SOLO MINI is another member of the family of SOLO Motor controllers, it has all the Hardware and Software features of SOLO UNO in a smaller form factor (74mm*63.6mm) with less power rating of 500Watts, the specifications of SOLO MINI are as below :
- Wide input voltage supply range from 6V to 40V
- The continuous output current of 20A, Max Current of 80A
- Capable of controlling DC, BLDC, PMSM, EC Coreless and ACIM motors
- Dual Core with parallel processing architecture
- Extremely fast FOC loop-rate up to 140kHz (7µs complete execution time)
- Bidirectional Regenerative Brake (maxed to current limit)
- Over-current, Over-voltage, Over-Temperature, Under-voltage and Reverse Polarity Protection
- Selectable output PWM switching frequency (from 8kHz to 80kHz)
- Automatic self-tuning and identification of Motor parameters
- Open-loop or Closed-loop Control modes
- Speed, Torque or Position control
- Advanced Sensor-less and Sensor-based Control
- Advance Field Oriented Control
- PWM and Analogue voltage input for Controlling Speed and Torque
- USB, UART, and CANopen Communication enabled
- SVPWM modulation
- Encoder and Hall Sensor Input with +5V supply
- +5V/1A (5W) output to supply external modules
- Updatable Firmware
- Heatsink mounted on the back of the board to enhance the thermal behavior
- 880µF onboard BUS capacitance
Make mistakes, safely
No matter how skilled, we all make mistakes. In hardware projects, this means losing time and money. We designed SOLO with safety in mind. We offer protection against reverse polarity connections, output short-circuits, over-voltage, or under-voltage on your main supply input (BUS) and over-current consumptions. You now use motors with fewer worries.
For experts and non-experts alike
SOLO is easy but not simple. The experienced user will find many advanced functionalities. From sending packets through USB, UART, or CAN to use industrial state of the art technologies like Closed-loop and Open-loop, Sensored, Sensor-less, and Field-oriented control.
Simply control the speed, torque, and position of your motor’s shaft separately. Enjoy these features while SOLO automatically detects the motor’s parameters and self-tunes.
Closed Loop Sensorless Speed Control
In sensorless mode, there’s no need to connect any sort of position sensors like Hall-Effect sensors or Encoders, and this will reduce the cost and wiring of the final products alongside with much higher reliability gained due to relying only on the electrical motor itself than anything else.
SOLO in this mode offers you a very robust experience even in very harsh conditions like below when the direction of the Brushless DC motor changes abruptly but as can be seen SOLO could fix the speed on both directions immediately with a very low error margin.
Closed Loop Sensorless Torque Control
The Torque control is done totally automatically in SOLO and the users by pushing down a button can immediately start utilizing it. In the image below you can see how SOLO kept the torque constant in a PMSM motor while the load was kept varying constantly.
Advanced Sensorless control with fast Angle Estimations
The sensorless methods are known to be based on approximations and estimations, which tends to degrade their accuracy in comparison with sensor-based methods, despite these facts, in SOLO you can find a very accurate sensorless estimator for speed and Angle which also is active, valid and functional during zero speed.
Closed loop speed or Torque control using Encoders or Hall-Sensors
Field Oriented Control (FOC)
Automatic Parameter Identification of Motors
Active Temperature Control
Our Latest Tutorial
When it comes to controlling the Position of a Brushless DC (BLDC) or a Permanent Magnet Synchronous Motor (PMSM) that are also known as BLAC using Raspberry Pi, you will need a Motor controller like SOLO that can deal with High powers injection into the Motors...
Speed and Torque Control of a Brushless Motor with Hall sensors using Arduino and SOLO [+ Arduino Code]
In this article we are going to talk about how to control Torque and then Speed of a Brushless motor of any kind from BLDC, PMSM or Coreless EC brushless motors using Hall sensors as their rotor position feedback precisely and efficiently, we are also going to use a...
In this article we are going to control the position of a Brushless DC or Permanent Magnet Synchronous Motor using SOLO with Arduino and more specifically using SOLO’s Arduino Library , in another word, we are turning SOLO into a precise servo drive to interface and...